使用 文字介面的 adsl-setup來設定ADSL連線
来源:百度文库 编辑:神马文学网 时间:2024/07/05 23:04:38
[root@proxy3 root]# adsl-setup
Welcome to the ADSL client setup. First, I will run some checks on
your system to make sure the PPPoE client is installed properly...
The following DSL config was found on your system:
Device: Name:
ppp0 DSLppp0
Please enter the device if you want to configure the present DSL config
(default ppp0) or enter ‘n‘ if you want to create a new one:
LOGIN NAME
Enter your Login Name (default 85545666@hinet.net):
INTERFACE
Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethX, where ‘X‘ is a number.
(default eth0):
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter ‘no‘ (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
Enter the demand value (default no):
DNS
Please enter the IP address of your ISP‘s primary DNS server.
If your ISP claims that ‘the server will provide dynamic DNS addresses‘,
enter ‘server‘ (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
Enter the DNS information here: 168.95.1.1
Please enter the IP address of your ISP‘s secondary DNS server.
If you just press enter, I will assume there is only one DNS server.
Enter the secondary DNS server address here: 210.240.232.1
PASSWORD
Please enter your Password:
Please re-enter your Password:
USERCTRL
Please enter ‘yes‘ (two letters, lower-case.) if you want to allow
normal user to start or stop DSL connection (default yes): no
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose ‘NONE‘ and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
Choose a type of firewall (0-2): 0
Start this connection at boot time
Do you want to start this connection at boot time?
Please enter no or yes (default no):yes
** Summary of what you entered **
Ethernet Interface: eth0
User name: 85545666@hinet.net
Activate-on-demand: No
Primary DNS: 168.95.1.1
Secondary DNS: 210.240.232.1
Firewalling: NONE
User Control: no
Accept these settings and adjust configuration files (y/n)?
[root@proxy3 root]# adsl-status
Note: You have enabled demand-connection; adsl-status may be inaccurate.
adsl-status: Link is up and running on interface ppp0
ppp0 Link encap:Point-to-Point Protocol
inet addr:218.161.1.240 P-t-P:218.161.0.254 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:1907281 errors:0 dropped:0 overruns:0 frame:0
TX packets:1553853 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2053873002 (1958.7 Mb) TX bytes:146972478 (140.1 Mb)
[root@proxy3 root]#adsl-start
[root@proxy3 root]#adsl-stop
from: http://poterp.iem.mit.edu.tw/linux/adsl-setup.htm
Welcome to the ADSL client setup. First, I will run some checks on
your system to make sure the PPPoE client is installed properly...
The following DSL config was found on your system:
Device: Name:
ppp0 DSLppp0
Please enter the device if you want to configure the present DSL config
(default ppp0) or enter ‘n‘ if you want to create a new one:
LOGIN NAME
Enter your Login Name (default 85545666@hinet.net):
INTERFACE
Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethX, where ‘X‘ is a number.
(default eth0):
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter ‘no‘ (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
Enter the demand value (default no):
DNS
Please enter the IP address of your ISP‘s primary DNS server.
If your ISP claims that ‘the server will provide dynamic DNS addresses‘,
enter ‘server‘ (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
Enter the DNS information here: 168.95.1.1
Please enter the IP address of your ISP‘s secondary DNS server.
If you just press enter, I will assume there is only one DNS server.
Enter the secondary DNS server address here: 210.240.232.1
PASSWORD
Please enter your Password:
Please re-enter your Password:
USERCTRL
Please enter ‘yes‘ (two letters, lower-case.) if you want to allow
normal user to start or stop DSL connection (default yes): no
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose ‘NONE‘ and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
Choose a type of firewall (0-2): 0
Start this connection at boot time
Do you want to start this connection at boot time?
Please enter no or yes (default no):yes
** Summary of what you entered **
Ethernet Interface: eth0
User name: 85545666@hinet.net
Activate-on-demand: No
Primary DNS: 168.95.1.1
Secondary DNS: 210.240.232.1
Firewalling: NONE
User Control: no
Accept these settings and adjust configuration files (y/n)?
[root@proxy3 root]# adsl-status
Note: You have enabled demand-connection; adsl-status may be inaccurate.
adsl-status: Link is up and running on interface ppp0
ppp0 Link encap:Point-to-Point Protocol
inet addr:218.161.1.240 P-t-P:218.161.0.254 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:1907281 errors:0 dropped:0 overruns:0 frame:0
TX packets:1553853 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2053873002 (1958.7 Mb) TX bytes:146972478 (140.1 Mb)
[root@proxy3 root]#adsl-start
[root@proxy3 root]#adsl-stop
from: http://poterp.iem.mit.edu.tw/linux/adsl-setup.htm
使用 文字介面的 adsl-setup來設定ADSL連線
adsl使用的常见协议
adsl
adsl
adsl
巧妙使用ADSL分流技术
ADSL的调试方法
利用ADSL猫指示灯识别ADSL的线路故障
ADSL Modem防火墙的配置
ADSL Modem防火墙的配置!
由于ADSL是电话铜线承载的一种宽带接入技术,电话线传输质量的优劣,直接影响到ADSL宽带的使用。在诸多的ADSL宽带故障是,掉线问题堪称一大顽疾,也是困扰ADSL用户的一种故障。ADSL掉线的问题比
ADSL知识
ADSL使用路由器出现FTP上传缓慢至0.0kb/s的解决办法
从细节入手 ADSL拨号提速私房秘籍挨个报 ADSL使用技巧
Linux ADSL拨号上网--鲁尼思的港湾
ADSL路由方式的NAT(端口映射)专题
ADSL宽带接入技术的原理和应用
ADSL宽带接入技术的原理和应用
常见ADSL断线网速慢的解决方法
常见ADSL断线网速慢的解决方法
让您的ADSL宽带再次提速
ADSL断线网速慢的解决方法
Linux ADSL拨号上网--鲁尼思的港湾
禁止ADSL路由器上网的破解方法